294ecfe782
hardware: pcb: add more copper to 1.2V line
...
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-08 19:11:24 +08:00
8050e796ab
hardware: pcb: clean up traces, widen up pours
...
Rework the traces somewhat to widen up the pours and remove some of the
bifurcation that's going on.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-08 19:07:56 +08:00
c2566ea16d
hardware: pcb: add version and update silkscreen
...
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-07 21:47:16 +08:00
db938e5557
hardware: pcb: first full routing of pcb
...
This passes DRC and has no unconnected nets.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-07 21:20:53 +08:00
140717e3c6
hardware: pcb: first unrouted layout of dvt1
...
This is just a placement test, to see if it can be laid out.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-06 19:44:12 +08:00
f9205b7027
hardware: pcb: replace pcb with usb-tomu version
...
We'll use this as a starting point, to maintain the same shape and size.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-05 13:03:07 +08:00
49d2924c26
hardware: pcb: redo timestamps, because kicad
...
kicad decided to redo all the timestamps. There are no other changes to
this commit.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-03 11:50:44 +08:00
25b662e6fb
hardware: pcb: re-route USB after flipping the footprint
...
It looks kinda janky, but it's better than ripping everything up and
starting over.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-02 20:39:32 +08:00
6214f995e9
hardware: pcb: increase USB connector size
...
It was only 11.3mm before. Make it 11.7mm, and center it.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-02 19:48:25 +08:00
e91896a8fb
hardware: pcb: loosen up the ground plane / 5V some more
...
Move some vias around to get the 5V plane more breathing room. Add a
small pour to give more copper and stabilize the net.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-02 19:22:29 +08:00
e48d836372
pcb: remove usb silk, add more 5V vias
...
Add more 5V vias near the 1.2V regulator, and replace a manual trace
with a copper pour. This will increase the amount of copper going to
both the 3.3V and 1.2V regulators, which should improve stability.
While we're at it, remove an errant silk artifact on the USB connector.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-02 14:03:27 +08:00
46fdfdf134
hardware: pcb: update drill offset, add mfg notes
...
Add a note indicating the PCB thickness and color.
Also, move the drill origin to the lower-left corner, to aid in machine
assembly.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-02 13:49:40 +08:00
12afe3aed1
pcb: add more silk, fatten up ground traces
...
Add more silk, indicating website and other info.
While we're at it, move some traces around to give more copper area, and
drop some more vias to improve ground performance.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-02 12:49:56 +08:00
d1923f10e1
hardware: pcb: finish layout with new PMOD connector
...
This is just about manufacturable.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-02 11:37:49 +08:00
b26b71343d
hardware: first fully-routed PCB
...
The PCB is terrible, and probably would have all sorts of issues. Will
rip it up and try again tomorrow.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-10-31 22:28:10 +08:00
e32b48a72e
hardware: pcb: initial commit
...
This is an initial commit. Still unclear of how big it will be, but
this is a good "minimum size" estimate.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-10-31 16:03:55 +08:00
ab33b4a0a1
hardware: rename tomu-fpga
to pcb
...
This more closely reflects what it actually is.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-10-30 17:05:02 +08:00