77d47db980
hardware: sch: add some spice models to passives
...
Identify passives and implement the various spice models.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-08 21:43:32 +08:00
d2b73fbc5e
hardware: schematic: rewire fpga as necessary for routing
...
FPGAs are great, because if there's an alternate method that's easier to
route -- go for it! This modifies some of the connections to ease
routing constraints.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-07 21:20:05 +08:00
596c686249
hardware: sch: complete schematic layout of DVT1
...
This is the first cut of a schematic layout of DVT1.
It includes all the decoupling caps still. We'll need to see if they're
kept around.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-06 19:43:31 +08:00
bbc18d2a90
hardware: sch: work-in-progress to go from QFN to WLCSP
...
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-05 13:03:36 +08:00
34f74fbf51
hardware: sch: first draft of dvt1
...
This removes much of the support debugging stuff from evt1. Still to
do:
- Assign footprints
- Figure out which PU resistor to include (if any)
- Figure out if we need to keep the USB buffering
- Remove extra decoupling caps
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-04 22:00:23 +08:00
da8ede5f75
hardware: fix USB footprint being mirrored
...
That could have been bad.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-02 20:38:34 +08:00
8bb0524872
hardware: sch: provide APN for RGB LED
...
Provide an alternate part number for the RGB LED, since the current one
is hard to source.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-02 19:48:25 +08:00
c02b3ef4ac
hardware: sch: add PMOD connector
...
Signed-off-by: Sean Cross <sean@xobs.io>
2018-11-02 11:37:40 +08:00
b26b71343d
hardware: first fully-routed PCB
...
The PCB is terrible, and probably would have all sorts of issues. Will
rip it up and try again tomorrow.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-10-31 22:28:10 +08:00
1acf50df39
hardware: sch: use footprints from tomu-fpga
...
Use our local copy of footprints, which are guaranteed not to change
between Kicad versions.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-10-31 16:03:06 +08:00
061b2c81a7
hardware: sch: map remaining footprints
...
Add footprints for the remaining schematic components.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-10-31 12:57:33 +08:00
a715f5c728
hardware: add testpoints for SPI programming
...
This will become necessary when doing factory burning.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-10-31 10:54:13 +08:00
30b7610996
pcb: hook up more debug wires
...
We have spare pins, so run more debug wires.
Many of these will probably get cut when doing the PCB layout.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-10-31 10:45:27 +08:00
4fe5f8f629
hardware: sch: use raspberry pi header, rework signaling
...
Rework the signaling to send everything to a Raspberry Pi header.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-10-31 10:36:01 +08:00
0973972464
hardware: pcb: add SPI debug header
...
This will be used to program SPI during board bringup.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-10-30 22:28:08 +08:00
78bb283bc6
hardware: sch: populate SPI, /RESET pullups
...
It turns out these resistors are important.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-10-30 19:21:01 +08:00
f06ef4a7d5
hardware: sch: add crystal, VCCPLL regulator
...
Add a crystal, so we can test to make sure it works.
Also add a second regulator dedicated to VCCPLL in an effort to
cost-down the capacitor and large components that shouldn't be
necessary.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-10-30 19:14:33 +08:00
ab18c90450
hardware: sch: specify spinor part
...
SPINOR parts are largely interchangeable. Pick one.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-10-30 17:09:11 +08:00
c7bfc248af
pcb: sch: renumber schematic
...
Renumber the schematic again, as things have shifted around a bit.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-10-30 17:06:04 +08:00
ab33b4a0a1
hardware: rename tomu-fpga to pcb
...
This more closely reflects what it actually is.
Signed-off-by: Sean Cross <sean@xobs.io>
2018-10-30 17:05:02 +08:00
